Humidity and temperature probes Rotronic HygroClip: HC2-S, HC2-S3, etc.

Purpose: primary conversion of humidity and temperature of the gas medium into digital and analog signals and data transmission to the hygrometer measuring unit.

Scope of application:

• measurement of humidity and air temperature;
• high temperature humidity measurements (+200°C), low temperature humidity measurements (-70°C);
• humidity at pressures from 0 to 100 atm.;
• high-precision relative humidity measurements;
• measurements in small volumes;
• measurement of the equilibrium relative humidity of paper and cardboard;
• moisture measurement of powders, granules, bulk materials;
• control of high-temperature drying, drying, baking processes;
• analysis of water activity of food products and raw materials;
• analysis of water activity of finished products and packaging quality.

Humidity and temperature probes. General description and comparison

HC2-S is a probe for indoor air, or in closed volumes, for operation at temperatures not exceeding +100 °C. A Teflon filter is installed on the probe to protect the sensor from dust and negative influences.

HC2-S3 is a probe for outdoor air, as well as as part of weather stations, for operation at temperatures up to -70 °C. A Teflon filter is installed on the probe to protect the sensor from contamination.

HC2-C04 is a probe with a cable for measuring the equilibrium humidity or water activity of raw materials, porous or bulk materials, paper, cardboard, textiles, air humidity. The diameter is only 4 mm. The probe has a sharp tip for piercing the material. There are micro slots on the housing for the penetration of water vapor to the sensor. The smallest humidity and temperature probe in the world.

HC2-C05 is a probe with a cable for air inside small volumes, with a diameter of 5 mm. There are micro slots on the housing for the penetration of water vapor to the sensor.

HC2-HK25 is a 250 mm long hand probe for air, for monitoring in closed volumes, air ducts at temperatures no higher than +150 °C. A steel mesh, Teflon or steel porous filter can be installed on the probe to protect the sensor from dust and negative influences.

HC2-HK40 is a 400 mm long manual probe for air, for monitoring in closed volumes, air ducts at temperatures no higher than +200 °C. A steel mesh, Teflon or steel porous filter can be installed on the probe to protect the sensor from dust and negative influences.

HC2-P05 is a hand-held probe for measuring the equilibrium humidity or water activity of raw materials, porous or bulk materials, paper, cardboard, textiles, air humidity. The diameter is 5 mm. The probe has a sharp tip for piercing the material. There are micro slots on the housing for the penetration of water vapor to the sensor.

HC2-HP28 is a 280 mm long hand probe for measuring the humidity of dusty or polluted air environments, the equilibrium humidity of materials during drying, and the water activity of the feedstock. It has a steel porous filter to protect the sensor from negative influences.

HC2-HP50 is a 500 mm long hand probe for measuring the humidity of dusty or polluted air environments, the equilibrium humidity of materials during drying, and the water activity of the feedstock. It has a steel porous filter to protect the sensor from negative influences.

HC2-HS28 is a 280 mm long hand-held bayonet probe for measuring the equilibrium moisture content of paper or cardboard.

HC2-HS42 is a 420 mm long hand-held bayonet probe for measuring the equilibrium moisture content of paper or cardboard.

HC2-ICxxx is a probe with a built-in extension cable, for measurements in a wide temperature range (from -70 to 200 °C), the diameter of the probe rod is 15 mm. The case is made of PEEK polymer. Various lengths of probes and built-in extension cables are available.

HC2-ICxxx-A is a probe with a built-in extension cable, for measurements in a wide temperature range (from -70 to 200 °C), the diameter of the probe rod is 15 mm in the tip and 25 mm in the base. The case is made of PEEK polymer. Various lengths of probes and built-in extension cables are available.

HC2-IMxxx is a probe in a stainless steel case, with a built-in extension cable, for measurements in a wide temperature range (from -70 to 200 °C), the diameter of the probe rod is 15 mm. Various lengths of probes and built-in extension cables are available.

HC2-iXXX is a probe with a threaded connection, in a stainless steel case, with a built-in extension cable, for measurements at pressures up to 100 atm. in a wide temperature range (from -70 to 200 °C). Various types of threads and built-in extension cables are available.

XB-OEM is a series of OEM humidity and temperature probes made of PEEK polymer or stainless steel, through-wall/cable versions. A wide range of designs is available, including various rod lengths, output signals, calculated humidity units, supply voltages. Bodyless versions are available.

XD-OEM is a series of OEM humidity and temperature probes made of PEEK polymer, rod design with built-in or removable extension cable. A wide range of designs is available, including various lengths of rods, digital and analog output signals, calculated units of humidity, supply voltage.

HC2 is an IP/IC/IT probe for indoor air, either in confined spaces where aesthetic appearance is important, or concealed mounting. It is installed in the walls of glass showcases and stands, laboratory installations and offices.

HC2-LDP is a dew point temperature probe (from -70 to 85 °C dew point) for monitoring compressed air, gases under pressure up to 100 atm., for monitoring compressor and adsorption drying systems, medical air, oil-free pumps. Threaded nozzles are available for connection to compression systems.

HC2-LDP-Ex - HC2-LDP probe in intrinsically safe (Ex) design.

• Humidity and temperature probes Rotronic HygroClip HC2A-S. Description of the vehicle type.

Catalog (eng)

Questionnaire